Page 1 of 1

Path edgeing.

Posted: Mon Dec 19, 2011 2:50 pm
by karl66
In the new year i plan to run a few paths from the top to bottom of garden. I only want them a couple of feet wide & i will put ornamental stone on them, i need some inexpensive ideas for a mini border either side of path, just something low level to stop the grass cuttings going onto stone path??. Bear in mind that with both sides i'll need about 240ft. karl.

Re: Path edgeing.

Posted: Mon Dec 19, 2011 2:53 pm
by GoggleboxUK
You could make your own using a section of plastic half pipe (like guttering) and concrete.

;)

Re: Path edgeing.

Posted: Mon Dec 19, 2011 5:41 pm
by karl66
Thanks goggle, its one for early spring. I was thinking of a wooden edgeing but it wont be as durable as a concrete one. karl.

Re: Path edgeing.

Posted: Mon Dec 19, 2011 7:56 pm
by Trudytropics
Pressure treated wood will give you 20years Karl, so not to be dismissed :wink:

Re: Path edgeing.

Posted: Mon Dec 19, 2011 8:02 pm
by karl66
Trudytropics wrote:Pressure treated wood will give you 20years Karl, so not to be dismissed :wink:
Trudy, do you mean the heavy duty log rolls?.

Re: Path edgeing.

Posted: Mon Dec 19, 2011 8:35 pm
by Adrian
Karl just get 4" x 1" pressure treated timber (from any timber merchant or diy chain) and some 2" x 1" pegs, that will be your cheapest option.
You can form either straight lines or steady curves and it will last for some time.

You want your mower to go over the edging or you will be doing a lot of strimming

Re: Path edgeing.

Posted: Mon Dec 19, 2011 10:37 pm
by Trudytropics
Adrian wrote:Karl just get 4" x 1" pressure treated timber (from any timber merchant or diy chain) and some 2" x 1" pegs, that will be your cheapest option.
You can form either straight lines or steady curves and it will last for some time.

You want your mower to go over the edging or you will be doing a lot of strimming
No not log roll but what Adrian said, dead easy to do, I'd use wooden stakes bashed in with a lump hammer, as long as everything is pressure treated it'll be fine, even if it starts to go in places, its easy to pull up and repair.

Re: Path edgeing.

Posted: Tue Dec 20, 2011 5:54 am
by karl66
Adrian wrote:Karl just get 4" x 1" pressure treated timber (from any timber merchant or diy chain) and some 2" x 1" pegs, that will be your cheapest option.
You can form either straight lines or steady curves and it will last for some time.

You want your mower to go over the edging or you will be doing a lot of strimming
Ade, not wanting to sound dense but unless the 4 x 1 was standing upright & not flat, how would this stop the stone flying over onto the grass & vice versa. karl.

Re: Path edgeing.

Posted: Tue Dec 20, 2011 10:55 am
by Trudytropics
Laying the wood on edge gives you 4" then bash stakes every couple of feet either side if needed, to be fair when we have done similar our wood was more like 6" but partly in the ground and then staked :D The bit that is the path needs soil and turf removing, membrane and decorative stone, it would ideally be 2 inches below edge of wood when filled with stone so as to not overflow onto grass, on the other side I'd just strim right upto wood. You will never keep all stone off grass and never keep grass cuttings off path unless you build a substantial wall :lol:

Re: Path edgeing.

Posted: Tue Dec 20, 2011 4:33 pm
by karl66
Trudy, thanks for that. I've been thinking at work today & i may push the boat out & use railway sleepers. karl.

Re: Path edgeing.

Posted: Tue Dec 20, 2011 4:43 pm
by Trudytropics
Karl I'm pretty sure you can get half railway sleepers, they are cut lengthways, so they are still chunky, but easier to cut and cheaper. In effect you get twice the length for the money, we used these on our veg beds a few years back. Not everywhere does them but might be worth enquiring when the time comes. :D